|
Side By Side Encoder can make one 3D high definition picture by compressing
2 pictures (L channel and R channel) into the horizontal direction.
Input signal is corresponding to HD-SDI signal.Output signal is HD-SDI and
DVI-D signal to connect with 3D display.
|
|
- It can encode one Side by side picture by compressing 2 pictures
(L channel picture and R channel picture).
2-channel HD-SDI input signals must be same format and gen-locked.
- Equipped with HD-SDI signal input / output based on SMPTE 292M and DVI-D
signal output.
It is not corresponding to Dual-Link and 3G-HD-SDI signals.
- It is possible to output the input signal without encoding (through) by the switch on
the front panel. L channel signal is output as it is.
- Size of the unit is 1U half rack size. Power supply to the unit is DC+12V.
It can operate by variable DC voltage from +9V to +18V.
Therefore, Lithium-ion battery can be connected.
- This equipment is corresponding to the HD signal of 1920x1080 4:2:2 format.
Input video signal format is recognized automatically.
1920x1080 format based on SMPTE 274M (60p/50p is not recognized).
1920x1080sF (segmented frame) based on SMPTE RP211-2000
Input/output video format is same.
- Thanks to DVI-D signal output, monitor corresponding to 3D can be connected.
3D display with more than 1920x1080 pixel resolution and vertical interleave
system. 3D display which can display the frame rate corresponding to 60P, 50P, 48P
- It is corresponding to HD-SDI multiplex signal (embedded audio, time code, etc).
Multiplex data of L channel is output.
- Delay time of HD-SDI input/output is less than 88μs.
|
|
2.1 Input/output video signal
| HD-SDI input |
| Input terminal |
BNC connector x2 (L channel / R channel) |
| Input impedance |
75Ω |
| Input return loss |
More than 15dB (5MHz or more) |
| Maximum input voltage |
±2V (DC + peak AC) |
| HD-SDI output |
| Output terminal |
BNC connector x2 (same output) |
| Output impedance |
75Ω |
| Output voltage |
800mVp-p ±10% |
| DVI-D output |
| Output terminal |
DVI-D connector x1 (Single-link 24bit) |
| Output format |
1920x1080 fixed
60P, 50P, 48P (different by input format) |
| Corresponding display |
Vertical interleave system 3D display
(More than 1920x1080 pixel) |
| |
| Input video format |
1920x1080 format based on SMPTE 274M
1920x1080sF 4:2:2 format based on SMPTE RP211-2000 |
recognition from following format;
080i/60, 1080sF/30, 1035i/60
080i/59.94, 1080sF/29.97, 1035i/59.94
080i/50, 1080sF/25
080p/30
080p/29.97
080p/25
080p/24
080p/23.98
080sF/24
080sF/23.98 |
2.2 General Characteristic
| Power supply |
DC +12V (+9 ～+18V) |
| Power consumption |
Less than 15W |
| Ambient temperature |
0°C ～ 40°C |
| Ambient humidity |
20 ～ 80% RH (No condensation) |
| Size |
EIA 1U half size
220(W) x 44(H) x 180(D) (Except projection) |
| Power supply connector |
4-pin Canon type connector, equivalent to HIROSE
HA16RA-4P
Pin assignment (1：GND 2：N.C 3：N.C 4：+12V) |
| Power fuse |
5A (Installed inside) |
|
3.1 Front Panel
| * Power Switch |
|
Turns ON/OFF the power.
ON/OFF operation shall be done with more than 2 seconds interval.
ON/OFF operation with short interval causes the trouble. |
| * Status Monitor Indication |
|
LCD display indicates the operating status and setting status. |
| * Function Set Switch |
|
Sets various function by [MENU] button, [SELECT] button, [EXIT] button.
Setting contents are memorized in the nonvolatile memory. |
| * THROUGH Switch |
|
By pushing [THROUGH] button, this machine can be made THROUGH mode.
To cancel, press the button once again.
THROUGH mode is not stored and returns to original status by turning the power ON again. |
3.2 Rear Panel
| * Power Input (DC +12V IN) |
|
DC +12V power input (+9 ～+18V)
4-pin Canon type connector, equivalent to HIROSE HA16RA-4P
Pin assignment (1：GND 2：N.C 3：N.C 4：+12V) |
| * REMOTE1 Connector |
|
Remote connector for external control. This is not used. |
| * REMOTE2 Connector |
|
Remote connector for external control. This is not used. |
| * HD-SDI (L) Video Input Connector (BNC) |
|
Input connector for HD-SDI signal.
Left eye video signal of 3D (L channel) is input.
As this equipment is operated locked up with this input,
please connect it without fail. |
| * HD-SDI (R) Video Input Connector (BNC) |
|
Input connector for HD-SDI signal.
Right eye video signal of 3D (R channel) is input. |
| * HD-SDI Output: Video Output Connector (BNC) |
|
Encoded video output with Side by side.
Each output is 2 distribution output.
(2 outputs are same output.) |
| * 3D Monitor Output: Video Output Connector (DVI-D) |
|
DVI-D connector for 3D display. |
|
|
|
|
